Charged right, not just topped up
Split AC refrigerant charging in Al Basateen
In Al Basateen, north Jeddah, split AC refrigerant charging demands precision because concentrated heat and humidity speed leaks in the joints. We diagnose the leak first, repair it, then vacuum and charge the line to the nameplate type and amount.
- Leak found first
- Vacuum and test
- Correct charge
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
When your split needs a refrigerant charge
- 1
Weak cooling with a clean filter
If the filter is clean and the compressor is running but the air from the indoor unit is barely cool, the cause is usually low refrigerant from a leak at the flare joints or the outdoor service valves.
- 2
Frost on the pipes or unusual water drips
Frost on the large pipe at the indoor unit, or water dripping from the unit in an unusual way, means refrigerant pressure has dropped below the range set by the manufacturer. The inspection finds the leak before any charging begins.
- 3
A split that was moved and refitted
When a split is removed for painting, renovation or a room move, the flare joints are disconnected and remade. These joints are the most likely source of a leak after refitting, and the system needs a careful check, a vacuum and a fresh charge.
Who it's for
Your bedroom split cools only at night
We find and fix the leak at the flare joints, then vacuum and charge to the nameplate refrigerant type.
Ask on WhatsAppYour split was removed for renovation and refitted
We inspect every remade flare joint, vacuum the full line, then charge and confirm cooling has returned.
Ask on WhatsApp
What the job covers
- Check flare joints and valves
- Repair or remake flare
- Vacuum line and pressure test
- Charge to nameplate refrigerant type
- Run unit confirm cooling
How we work
How we work
- 1
Describe the fault
Tell us on WhatsApp what is happening and send a photo of the outdoor unit nameplate so we know the refrigerant type before we arrive.
- 2
Inspect and find the leak
The technician checks the flare joints at the indoor unit and the service valves at the outdoor unit and locates the leak before taking any further step.
- 3
Repair and vacuum
We tighten or remake the flare joint as its condition requires, then vacuum the line and watch the pressure hold to confirm the line is tight.
- 4
Charge and run
We charge with the nameplate type at the amount the inspection determines, then run the unit and confirm that cooling has returned to the normal level.
Fix the leak first or just top it up?
| Alrabih | The usual way | |
|---|---|---|
| The leak | Found and fixed first | Ignored, charged over it |
| Flare joint | Checked, remade if needed | Not checked |
| Vacuum | Before every charge | Often skipped |
| Refrigerant type | Nameplate only | Whatever is available |
| Line moisture | Removed by vacuum | Left inside the line |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.

Split AC installation
Request this service
Duct installation
Request this service
Central AC installation
Request this service
Duct fabrication
Request this service
Cold room installation
Request this service
Electro-mechanical works
Request this service
Chiller & AHU installation
Request this service
HVAC design
Request this service
AC repair & faults
Request this service
AC cleaning
Request this service
Refrigerant charging
Request this service
Central AC maintenance
Request this service
Chiller maintenance
Request this service
AC removal & refitting
Request this service
Duct cleaning & sanitising
Request this service
AC servicing by brand
Request this service
Operation & maintenance contracts
Request this service
AHU maintenance
Request this service
Fridge & freezer service
Request this service
Cold rooms
Request this service
Display fridges & chillers
Request this service
Factory HVAC
Request this service
Warehouse HVAC
Request this service
Villa & home HVAC
Request this service
Hotel HVAC
Request this service
School HVAC
Request this service
Hospital HVAC
Request this service
Mosque HVAC
Request this service
Mall & retail HVAC
Request this service
Restaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.

What sets this district apart
Al Basateen is a medium residential area with villas and flats with green spaces and home gardens, where summer heat concentrates due to direct sun on facades and roofs and limited natural shade from older trees in some areas. High heat and humidity together speed copper joint oxidation and refrigerant leaks, worsening if the leak source is not properly repaired before recharging.
Al Basateen is in north Jeddah, a medium residential area with villas and flats with gardens and trees, away from the direct coast but exposed to concentrated solar heat.
Most split units here are medium to high-capacity (1 to 2 tonnes), with outdoor units on side walls or roofs with partial shade from trees.
The AC setup in Al Basateen
- 1
Medium split on partially shaded side wall
Most outdoor units here are on side walls with partial tree shade, but heat still concentrates during peak summer.
- 2
Multiple split units in villa or flat
Larger villas and flats here need multiple units (bedrooms, living room, kitchen), each requiring separate inspection and charging.
- 3
Copper runs exposed to heat and humidity
The copper line from outdoor to indoor unit crosses areas exposed to heat and humidity, speeding leaks and corrosion.
Before the visit
Before our visit in Al Basateen
- 1
Ensure access to the outdoor unit
If the unit is on a side wall or roof, ensure the path is clear of dense trees or cables before the visit.
- 2
Check copper joints for moisture and corrosion
Before the visit, notice any moisture, dripping or green corrosion coating on joints and let us know their location.
- 3
Clear safe space around the outdoor unit
Ensure no dense trees, wires or obstacles block safe access to the joints and pipes for the team.
More districts for Split AC refrigerant charging
Other services in Al Basateen
FAQ
Questions about Split AC refrigerant charging
Does the split have to come off the wall to be recharged?
Usually not. Charging is done at the service valve on the outdoor unit, and if the leak is at the flare joints behind the indoor unit we reach them by lifting the lower cover or tilting the unit on its bracket. It only comes down when the joint is inside the wall.
Where do leaks usually occur in a wall split?
The most common points in a wall split are the flare joints at the indoor unit, which loosen over time from vibration, and the service valves at the outdoor unit. In Jeddah's humid and salty air, oxidation at copper connections can develop faster, which raises the chance of a leak.
Does the charging process differ when a split has been moved?
When a split is moved, the flare joints are disconnected and remade, and this is when air and moisture enter the line. A full vacuum before charging becomes especially important, and the technician checks every remade flare joint before the line is closed.
Why does my split cool only at night?
This is a common sign of low refrigerant. At night, lower outdoor air temperature lets the compressor partly compensate for the shortage. During Jeddah's daytime heat, the reduced charge is not enough and cooling weakens or stops. The inspection confirms whether this is the cause or whether another factor such as the compressor or capacitor is involved.
Does the length of the copper pipe run affect how much refrigerant is needed?
Yes, a longer copper pipe run between the two units requires more refrigerant. The site inspection measures the actual run length, and the technician sets the charge amount based on the nameplate figure and the installed pipe length.
Does the AC lose cooling fast in Al Basateen's summer, is it low refrigerant?
Could be a leak reducing refrigerant, and summer heat speeds the loss. We find and repair the leak first before recharging.
Do heat and humidity together in Al Basateen affect refrigerant more?
Yes, concentrated heat and high humidity together speed copper joint oxidation and refrigerant leaks faster than cooler areas.
The outdoor unit is partially shaded by trees, does this help?
Yes, partial shade reduces direct heat on the unit, but trees may block ventilation. We ensure during inspection that airflow is adequate and leaves don't block openings.
After leak repair and charging, how long before new issues in Al Basateen?
If we repair the root leak properly and charge to exact specs, the unit works well. But checking joints once or twice yearly helps detect new leaks from ongoing heat and humidity.












































































