Window unit to split
Window-to-split conversion in Mushrifah
In Mushrifah, central Jeddah, converting window AC to split restores light and security to your window. We seal the opening with blockwork, insulation and paint, and install a new split through a small secure hole.
- Sealed opening
- Window restored
- Quiet split
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
Why owners make the switch
- 1
Non-stop noise from the old unit
The window unit motor runs right inside the room, and the vibration gets worse over the years. Many owners say sleeping next to it has become impossible, and switching to a split removes the source entirely.
- 2
The wall opening lets in heat and dust
The foam and tape sealing the gap around a window unit frame degrade in Jeddah's salty, humid air. The large opening becomes a clear source of heat loss, dust in the windy season and sometimes rain in winter.
- 3
The blocked window darkens the room
A window unit fills the whole window or most of it, so the room loses its natural light and ventilation at times when you do not need cooling. Getting the window back fully changes the room noticeably.
Who it's for
Own a villa and want the windows back
We remove the window units from your villa rooms, close each opening with block, insulation and plaster, then fit a split in each room through its own core hole.
Ask on WhatsAppManaging a rental flat and want to raise its value
We convert the flat's window unit to a quiet split and restore the wall and window to their original condition, improving the unit for the next tenant.
Ask on WhatsApp
What the conversion covers
- Remove old unit and frame
- Block plaster and insulation
- Paint inside and outside
- New core hole for split
- Insulated copper and drain
How we work
How we work
- 1
Survey the wall and opening
We check the wall thickness and the build around the old opening, agree where the new core hole for the split goes away from the old frame, and decide where the outdoor unit will sit.
- 2
Remove and close
We remove the window unit and its frame without breaking the surrounding wall, then close the opening with blockwork or lightweight concrete to match the original construction, with thermal insulation set inside the layers before plastering.
- 3
Plaster and paint both sides
We plaster and paint the closed opening on both the inside and outside faces to match the existing wall, leaving no trace of the old opening that could let in air or moisture.
- 4
Fit the new split
We core the agreed spot for the split, run insulated Mueller copper and a drain line with the correct fall, vacuum the line before start-up and test everything with you present.
A proper seal or a quick patch?
| Alrabih | The usual way | |
|---|---|---|
| Closing the opening | Block, plaster and insulation | Foam or a timber board |
| Outside face | Plastered and painted flush | Visible mark or cracks |
| Thermal insulation | Inside wall before plastering | None |
| New split core hole | Chosen away from old frame | Wherever drilling is easiest |
| Outside paint | Matched to existing wall colour | Different colour or unpainted |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.
Split AC installation
Request this serviceDuct installation
Request this serviceCentral AC installation
Request this serviceDuct fabrication
Request this serviceCold room installation
Request this serviceElectro-mechanical works
Request this serviceChiller & AHU installation
Request this serviceHVAC design
Request this serviceAC repair & faults
Request this serviceAC cleaning
Request this serviceRefrigerant charging
Request this serviceCentral AC maintenance
Request this serviceChiller maintenance
Request this serviceAC removal & refitting
Request this serviceDuct cleaning & sanitising
Request this serviceAC servicing by brand
Request this serviceOperation & maintenance contracts
Request this serviceAHU maintenance
Request this serviceFridge & freezer service
Request this serviceCold rooms
Request this serviceDisplay fridges & chillers
Request this serviceFactory HVAC
Request this serviceWarehouse HVAC
Request this serviceVilla & home HVAC
Request this serviceHotel HVAC
Request this serviceSchool HVAC
Request this serviceHospital HVAC
Request this serviceMosque HVAC
Request this serviceMall & retail HVAC
Request this serviceRestaurant & cafe HVAC
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we've completed in Jeddah.
Customer reviews
What our customers say
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewService areas
We come to you anywhere in Jeddah
From Al Shiraa and Al Yaqout in the north to Al Thaghr and Al Quraiyat in the south, with our base in Al Aziziyah.
What sets this district apart
Mushrifah is a dense residential district with multi-storey apartment blocks and a diverse community, and many residents complain of lost natural light and air from large window units covering windows. Buildings here are close together and outer walls are relatively thin, requiring precision when drilling new holes and coordination with building management and security for pre-approval. The extra challenge is keeping the building's appearance intact as outdoor units multiply on the facades.
Mushrifah sits in central Jeddah's crowded residential zone, a district of multi-storey blocks with narrow facades and diverse residents.
Most Mushrifah blocks have thin shared outer walls, and drilling a split hole requires precise assessment of wall thickness and internal pipe routing.
The AC setup in Mushrifah
- 1
Carefully sited split hole in a thin wall
In Mushrifah, the hole is drilled with precision in a safe spot clear of pipes and internal wall structures.
- 2
Secure sealing of the old opening
We seal the window opening securely to prevent hot air or moisture ingress, finishing with uniform exterior paint.
- 3
Safe outdoor unit mounting on crowded facades
The outdoor unit is secured firmly on a bracket or balcony in a way that does not block windows or compromise building safety.
Before the visit
Before our visit in Mushrifah
- 1
Get building management and security approval
Contact building management or security before the visit to inform them of the planned small-hole work.
- 2
Ensure safe access to the external facade
Confirm the team can safely reach the outer wall using secure ladders or from your balcony.
- 3
Identify location for the outdoor unit
Choose a safe spot on your balcony or on the metal bracket we will mount on the facade, away from pathways and windows.
More districts for Window-to-split conversion
Other services in Mushrifah
FAQ
Questions about Window-to-split conversion
Do you restore the original window after closing the AC opening?
It depends on what the original opening was. In some rooms the opening was cut into a solid wall with no window frame, so it is fully closed. If the original build can take a window, we discuss that at the survey and tell you what is actually possible in your wall.
Can the old window unit hole be reused as the new split core hole?
The old opening is usually much larger than the small core a split needs, and its position may not suit the copper and drain route. It is safer to close it fully and drill a new hole in the right place, so no hidden gaps remain to let air through or collect moisture.
How do you stop humid salty air coming through the closed opening?
We place thermal insulation inside the wall layers before plastering, and use sealing materials that form a continuous barrier from inside to outside. Jeddah's combination of humidity and salt accelerates the breakdown of any temporary patch, so we treat the closed opening as a new wall section, not a surface repair.
Do I need permission from the building management before closing the opening?
In a rented flat it is wise to check with the owner or management office first, because the work changes the building's outside face. In a villa you own the decision is yours. We explain the full scope at the survey so you can get any approval needed before the work day.
Does the job change if the wall is concrete rather than block?
Yes. A concrete wall needs a different filling method and may require a repair mix rather than standard block. We identify the wall type at the survey and choose the material that bonds solidly with the existing concrete, leaving no hidden gaps for moisture to enter later.
Our building's walls are thin, can you drill a split hole safely?
Yes, we use precision drilling techniques and inspect the full wall beforehand to confirm structural safety and no interference with internal pipes.
Does building management require approval for a new split hole?
Yes, each block has its own rules. We recommend telling building management and security in advance, and we can help explain the small hole and that it does not compromise the building.
My window gets almost no natural light because of the window unit, will split solve this?
Yes, split opens the window fully, restoring natural light and fresh air to the room, which improves comfort and well-being.
Where do you put outdoor units if balconies are small and crowded?
We pick a safe spot on the balcony or mount it on a strong metal bracket on the outer facade so it does not block residents' movement.
