Testing and commissioning in Madinah, Madinah Region
Testing and commissioning systems in Madinah begins with complete pressure, leak and vacuum checks after final installation. We then start the system, measure temperature and airflow at each outlet and balance all rooms, bathrooms and hallways before handover.
4.9 on Google- Line test
- Air balance
- Controls set
Clients We're Proud to Serve
Organisations and companies that trusted Alrabih with their projects.
Is it for you?
When commissioning becomes necessary
- 1
A new system before handover
The contractor has finished and handover is due. Before the owner signs off, you need confirmation that the line is tight, the ductwork distributes air evenly and the thermostat controls the system as designed. No earlier stage replaces this step.
- 2
A major change to an existing system
Rooms have been added, a large duct section replaced or the central unit changed. A major modification shifts the pressure and airflow balance across the whole system and calls for a full test as if it were new.
- 3
Rooms that cool unevenly
Some rooms are too cold while others barely cool, even though the system runs. The cause is usually dampers that were never balanced or air outlets sized for a different room, both of which are corrected during the balancing stage of commissioning.
Who it's for
Your new villa is ready for contractor handover
We test the refrigerant line, ductwork and every air outlet, set the dampers and check the thermostat before you accept the system from the contractor.
Ask on WhatsAppYou have added floors and modified the AC system
A major modification shifts balance across the whole system. We test pressure and airflow and reset every damper across all zones.
Ask on WhatsApp
What the job covers
What the commissioning covers
- Line pressure and vacuum test
- Electrical circuits and protection checks
- Air temperature at every outlet
- Damper adjustment for room balance
- Thermostat and control panel check
How we work
How we work
- 1
Pre-start check
Before start-up the technician checks copper joints, ductwork connections and wiring, and confirms insulation is intact and ducts are clear. A fault found before start-up is far easier to correct than one found after.
- 2
Line test
We pressurise the refrigerant line and watch the reading to confirm no leak, then vacuum the line to remove air and vapour, hold the reading steady, and only then release the refrigerant.
- 3
First start-up and airflow
We start the system and measure the air temperature at every outlet, then adjust each damper until the rooms reach the temperatures the system was designed to deliver.
- 4
Controls check and handover
We test the thermostat and any control panel, confirm the system responds to every command, then show the owner how to set the thermostat and the right setting for each room before we hand the system over.
Why Alrabih?
Planned commissioning or a quick switch-on?
| Alrabih | The usual way | |
|---|---|---|
| Leak test | Pressure and vacuum test | Start-up with no test |
| Room balance | Each damper measured and set | Uneven cooling left as is |
| Electrical check | Protections and wiring reviewed | Only visual power-on |
| Controls | Thermostat set and tested | Left on its first setting |
| Plenum box | Distribution checked from plenum | Not checked |
Everything your AC needs, from one team
From system design and duct fabrication to installation, commissioning and maintenance.

Split AC installation
Request this service
Duct installation
Request this service
Central AC installation
Request this service
Duct fabrication
Request this service
Cold room installation
Request this service
Electro-mechanical works
Request this service
Chiller & AHU installation
Request this service
HVAC design
Request this service
Copper piping works
Request this service
Air outlets and grilles installation
Request this service
Ventilation and exhaust systems
Request this service
HVAC controls and automation
Request this service
Duct insulation
Request this service
AC repair & faults
Request this service
AC cleaning
Request this service
Refrigerant charging
Request this service
Central AC maintenance
Request this service
Chiller maintenance
Request this service
AC removal & refitting
Request this service
Duct cleaning & sanitising
Request this service
AC servicing by brand
Request this service
Operation & maintenance contracts
Request this service
AHU maintenance
Request this service
Testing and commissioning
Request this service
Fridge & freezer service
Request this service
Cold rooms
Request this service
Display fridges & chillers
Request this service
Factory HVAC
Request this service
Warehouse HVAC
Request this service
Villa & home HVAC
Request this service
Hotel HVAC
Request this service
School HVAC
Request this service
Hospital HVAC
Request this service
Mosque HVAC
Request this service
Mall & retail HVAC
Request this service
Restaurant & cafe HVAC
Request this service
Government building HVAC
Request this service
Sports club HVAC
Request this service
Tower and office building HVAC
Request this service
University HVAC
Request this service
G90 galvanized steel and aluminium sheets
Request this service
Mueller and Lawton copper pipes
Request this service
Air grilles and diffusers (Saudi-made)
Request this service
Central AC accessories and materials
Request this service
Some of our work
Ductwork, rooftop units and diffusers, from work we have completed.
Customer reviews
What our customers say
- Waleed Daadouch
“The nicest treatment from the showroom team, and their prices are very competitive.”
Translated from Arabic
- Muhammadramzan 2641
“MashaaAllah. Services are so good. Behaviour and kindness 100/100. Prices are less then Market. Fully recommended”
- RHAM rhamLocal Guide
“May God grant them success. Refined and respectful treatment.”
Translated from Arabic
- shahzeb armani
“Wow. Prices are so comfortable. Outstanding services. People are so talented and nice”
- Shakeel Ahmed
“Nice experience very cooperative. Nice conducting with all customers”
- Tawfik AlyawerLocal Guide
“U can find all u need for air conditioning”
Your satisfaction matters to us! If you had a great experience with us, we'd love a 5-star rating and a kind review.
Worked with us? Leave a reviewWhere we work
Testing and commissioning in cities near Madinah
We are based in Jeddah, and we supply duct and install across the Kingdom. All our services in Madinah
What sets this city apart
Madinah has hotels and high-rise apartments near the centre, villas and apartments on the plateau, plus government schools and hospitals. Summers are very hot, winters mild, and post-installation testing requires careful verification of duct and copper insulation especially in government and service buildings with continuous operation. In hotels and compact apartments we test each unit separately to ensure balance and comfort in every space.
Madinah lies in the Medina Region on a plateau with volcanic fields and palm groves, with hot desert summers and mild winters, built with hotels, towers, villas and apartment buildings.
In Madinah hotels and apartment buildings every separate unit is tested for airflow and pressure, and roof and inter-unit air leaks are verified absent.
The AC setup in Madinah
- 1
Testing separate units in apartment buildings
In a multi-unit apartment building we test each flat or townhouse separately and verify no cold air crosses between units through duct or openings.
- 2
Temperature measurement in medical wards
In hospitals and clinics we measure temperature in operating theatres, intensive care and general wards where requirements differ, ensuring each reaches its target precisely.
- 3
Airflow testing in classrooms
In schools we test inlets and returns in each classroom and verify even distribution without strong drafts that might disturb students and teachers.
Before the visit
Before our visit in Madinah
- 1
Prioritize sections and units for testing
Tell us the order of sections or units to test first, especially in hospitals and schools that may start operations in phases.
- 2
Prepare the site and staff for testing
Ensure test rooms are empty of people and other equipment, and tell us any security or health restrictions that might affect testing times or access areas.
- 3
Provide a route for duct and copper from roofs
Ensure duct and copper runs from roofs or outdoor areas are protected from construction or cleaning work and tell us of any obstacles needing site coordination.
Other services in Madinah
FAQ
Questions about Testing and commissioning
What is the difference between installation and commissioning?
Installation means fitting and connecting the parts. Commissioning comes after, to confirm that what was fitted works as designed: the line is tight, air reaches every room in the right quantity and the thermostat controls accurately. The two stages are different and neither replaces the other.
Does a small building need full commissioning?
Building size does not decide whether commissioning is needed. Even in a small flat or villa there may be a refrigerant leak or a damper that leaves one room far colder than another. The site and the system design decide the scope of testing required, and that becomes clear at the survey.
Why do you rely on a stable vacuum reading rather than a fixed time?
The amount of vapour trapped in a refrigerant line varies from one site to another depending on the building's conditions and its city's climate. Vapour left in the line gradually strains the compressor and weakens cooling. We therefore run the vacuum pump until the reading reaches a stable level, and only then open the refrigerant.
What if one room is still warmer after commissioning?
We go back to the air temperature at that room's outlets, check the damper and the flexible duct that feed it, and confirm the air outlet suits the room's size. Adjusting the damper is usually enough; if the cause lies in the system design itself, we explain the right solution before any further work.
Do flexible duct connections need checking during commissioning?
Yes. A flexible duct connecting a rigid duct run to an air outlet can crack or partly detach during installation without being obvious. That gap reduces air reaching the room and makes balancing readings unreliable. The technician therefore inspects every flexible duct connection before measuring airflow at the outlets.
How do we test school and hospital systems in Madinah?
We check pressure, leaks and vacuum early without disturbing staff, then operate during off-duty times, measuring temperatures and airflow in each classroom, room and clinic per health needs.
Does testing differ between a villa and apartment building in Madinah?
Yes. A villa is one system tested once, but an apartment building has separate units, so we test each unit independently to verify insulation between them and balance within each flat.
How long does testing and commissioning take in a Madinah hospital?
Duration depends on hospital size, ward and clinic count, set after we review drawings and site. We agree the testing schedule with hospital management to avoid disrupting staff and patients.
Does testing and commissioning reveal the quality of insulation and installation?
Yes. We measure heat loss, leaks, pressure and airflow balance at each outlet, so any insulation or joint issues appear in results, documented in the handover record with recommendations.


























































































